Aug 06, 2014  download instrucciones lavadora bluesky blf 1011 sp. File name: manual_id280638.pdf Downloads today: 187 Total downloads: 5701 File rating: 8.45 of 10 File size: ~1 MB >>> DOWNLOAD. Download instrucciones lavadora bluesky blf 1011 sp File name: manual_id280638.pdf Downloads today: 187 Total downloads: 5701 File.

• 15935 Answers SOURCE: A lot of concerns have been raised about door bellows molding, mildewing, and/or ripping and needing replaced. A replacement bellow isn't cheap (prices vary, but are around $75-80), so hopefully these helpful steps will eliminate the need to call a repair service and pay the additional labor charges. This is a repair of MODERATE difficulty.

Just follow these steps: 1. Unplug the washer. Remove the washer top panel by removing the three torx-type screws (or 7mm) where it attaches in the rear of the washer. The panel should slide back, and then lift off.

Remove the operator console by removing the dispenser and the scew(s) behind it. Take a putty knife and insert it under the console seam right above the door. If you push in slightly while pulling outwards the panel pops off. Use care not to pull or damage any of the wiring.

You can leave the wires attached and simply lay the console across the top of the washer out of the way. Locate the wire hoop retainer around the rubber door boot. It is located behind the rubber seam where it attaches to the door frame. Follow this hoop around to the bottom of the door opening and locate the wire tension spring. Gently pry this spring apart and pull the wire hoop from the groove. Pull the rubber boot from the frame and push it inside towards the wash tub.

You will also have to remove the door boot from the fill tube on the left hand side of the door opening. There is a small wire clamp holding it in place. Remove the three screws that hold the door latch assembly in place. This is on the right hand side of the door opening. You can leave the latch in place as long as you remove the screws and push it inside slightly to remove it from the front casing of the washer. Remove the door by removing the screws holding the hinges in place.

Use care to support the door hinges when loosening. They can bend. Set the door aside in a location where it will not get stepped on or broken. Remove the lower kick panel under the door. There are 3 screws under the bottom edge holding it in place.

Sometimes the panel can stick. A slight tap on either side will knock it free.

Remove the front washer casing by removing the four remaining screws that are holding it in place. There should be two at the top and two at the bottom. Set the front casing aside. Remove the old door boot by locating the large clamp that attaches it to the wash tub. Loosen the 7mm nut and the boot will detach from the tub. Also remove the boot from the fill tube coming from the dispenser. Install new door boot on the wash tub and install clamp.

There should be instructions that come with the door boot with guide marks to ensure you align it correctly. Once you have the boot in place, tighten the clamp enough to where it is snug. Mortal kombat 9 for pc. DO NOT over-tighten or you may damage the tub and or clamp. In most cases the clamp will break. Once you have the boot in place, re-install everything in the reverse order of how I explained to disassemble.

Make sure you connect the door latch assembly BEFORE you re-install the outer portion of the door boot. Also, make sure you install the boot completely over the fill tube. There should be a ridge on the tube where to stop. Sometimes the tube is not inserted all way into the boot and water will leak behind it. The clamp is always difficult to get back in place.

If you cannot get the clamp to go back over the tube, you can live without it. Some newer models do not have them installed. Just make sure it is a snug fit where the rubber boot fits ALL the way back to the plastic ridge on the tube. When you get the point where you are ready to install the door boot back over the frame of the door opening ensure you fit it snugly all the way around the door. Beginning at the top of the door, start inserting the wire hoop back into the groove.